These waterproof boots let you progress in maximum comfort with good support on relatively difficult trails with a moderate to steep slope.Looking for some reassuring boots that will stand the test of time? By its authenticity, 100% full-grain leather, this model has the comfort and all-round durability you need in the mountains
European made 100% of our Forclaz boots are manufactured in Europe
These shoes are manufactured in the European Union, in Romania, in a factory that specialises in making hiking boots. (Rekord)
VIBRAM®. Grip and traction of our soles
VIBRAM® branded sole with excellent grip on all terrain, dry or wet, earth or rock. Basically invincible!
The studs will also provide grip on muddy and damp terrain
“average width sole”. The wider the sole, generally the more flexible it is. Therefore, with this sole it’s comfortable to walk on most trails without losing stability
Waterproofing test carried out on this model
This boot has been validated by a waterproofing test at 50,000 repeatable flexes, i.e. 20 km – 8 hours of walking in water up to the mid-upper, which today guarantees an excellent level of waterproofing for your boots.
--> Our assessment indicates a LEVEL OF 4/5 giving 8 hours of waterproofing when hiking in the rain.
The details of tests carried out to assess the waterproofing of our boots is below, in the features section.
Increase your boot’s waterproofing with a gaiter
The waterproofing of boots is often compromised because water gets in at the collar of the boot.
--> To keep your feet dry for longer, it is advisable to use a waterproof gaiter or mini-gaiter that will prevent water as well as pebbles and sand from getting inside through the top of the boot.
Model perfectly suited to this trekking gaiter MT500 black
https://www.decathlon.co.uk/p/trek-500-trekking-gaiters-black/_/R-p-124466?mc=8347880&c=BLACK
Make the waterproofing of this textile model last longer
Even though this model has a membrane (waterproof, breathable), it is recommended you use a re-waterproofing spray a few times a year to restore the original water-repellent properties and prevent staining of the outer material.
--> It revitalises the water-repellent properties of the outer material (water runs off and doesn’t soak in). Each fabric section is sprayed taking care not to forget the thread in the seams (water loves seams!!)
Waterproofing my textile boots with a reactivating spray
1 / Use a brush and/or a sponge to clean; remove any soil or mud.
2/ Then leave to air dry, away from any heat source.
3 / Shake the WATERPROOF SPRAY can / €5
4 / Spray the product from a distance of 25 cm
5 / Leave for at least 10 minutes. Caution: Do not rub or wipe.
Link to SPRAY below
https://www.decathlon.co.uk/p/100-ml-waterproof-stain-resistant-spray-for-leather-and-textile-walking-shoes/_/R-p-312940
Lab tests
Laboratory tests were conducted to test the following elements:
– tearing of the eyelets and straps
– bonding of the sole
– toxicology
– UV resistance
– abrasion of the sole and components of the upper
– accelerated ageing.
CAN CRAMPONS BE USED WITH THESE TREKKING BOOTS?
This model of Trekking boot allows for the occasional use of STRAP-ON CRAMPONS ONLY. It is sufficiently rigid for the occasional use of strap-on crampons while guaranteeing extremely good comfort when walking.
Choosing your size is an important point.
For hiking, do not hesitate to buy one size larger than the usual size to guarantee excellent comfort on the descent and to avoid toes rubbing at the tip of the shoe. Tip: keep your toenails short and, before descending, check that your lacing prevents your foot from sliding forwards inside the boot.
5 levels of waterproofing
During the waterproofness test, we test 5 levels of waterproofness:
2,000 flexes (approximately 4 km ,30 minutes of walking)
10,000 flexes (approximately 10 km ,3 hours of walking)
30,000 flexes (approximately 15 km ,6 hours of walking)
50,000 flexes (approximately 20 km ,8 hours of walking)
100,000 flexes (approximately >20 km ,24 hours of walking)
WATERPROOFING TEST / 100% WATERPROOF laboratory-tested
Our boots are laboratory tested according to two successive tests
Test 1 / We test the efficiency of the membrane only when it is pressured and placed in water, we check the absence of water on the surface, like when you test a punctured inner tube.
Test 2 / Thanks to mechanical arms that simulate walking, the assembled boots are half immersed in water and they complete thousands of flexes to check that the inside of the boot remains dry and it is therefore waterproof.
BUYING TIPS / HOW DO YOU TRY YOUR BOOTS ON?
How to choose your boots:
1. Try on both shoes, standing up, with the socks worn for hiking.
2. Tighten the laces correctly
3. Check the following two areas of comfort: the base of the heel and the front part of the foot going down.
4. Stand up to walk with the boots on.
5. Try on several sizes and several models.
6. Break in your boots gradually during their first hikes to adapt them to your foot

























Reviews
There are no reviews yet.